美國的斜齒輪圖紙的英文,誰能幫忙翻譯下,不勝感激!

yang13564

1.
% u) D/ A, }2 \, L# g5 oQuality: ANSI/AGMA 2000-a88-q11, full depth, full fillet.

2.
FOR LEAD, CROWN, AND PROFILE TOLERANCES SEE DWG 54773379

3.
: E4 W8 c* o8 S" sCROWN DRIVEN GWAR ONLY

4.
: z, L( I! Y! D* x9 U, bNORMAL PRESSURE ANGLE 20”

5.
/ m7 M* c9 d1 l5 |& f' ZNORMAL DIAMETRAL PITCH 8

6.
# H4 ?& e4 v5 t: _' h6 T8 ~: q, f9 v3 sNORMAL CIRAULAR PITCH 0.3927

7.
! p0 s2 h" o1 p- \7 I7 J9 e5 j0 i6 |HELIX ANGLE:16.6011

8.
BACKLASH TO BE 0.996” TO 0.008” ON 6.9784” CENTERS

9.
- H* b9 a: ]3 Z( p0 w) G9 h. ~8 V6 kMATERIAL: AISI 8620

10.
CASE CARBURIZE TO 0.025” TO 0.040” EFFECTIVE FEPTH AFTER GRINDING AND HARDEN TO 57-61 RC, CORE HARDNESS
7 B+ h: A+ Z3 \3 a! e2 MTO BE 25-40 RC.

11.
RETAINED A USTENITE – 5% MAXIMUM BY VISUAL INSPECTION.

12.
EACH GEAR DEAR SET TO BE BOXED SEPARATELY AS A SET AND EACH GEAR MARKED WITH THE SET PART NUMBER ON THE OUTSIDE. EACH GEAR TO HAVE P/N AND SUPPLIER INENTIFICATION STAMPED. EACH GEAR TO HAVE P/N AND SUPPLIER IDENTIFICATION SATAMPED OR ELECTRIC ACID ETCHED AS SHOWN, APPROX. TEXT HGT..25’.

13.
9 }- R1 z3 o3 M* E+ H+ ]! j$ JREMOVE ALL CHIPS FROM TAPPED HOLES.

NUMBER OF TEETH

HAND OF HELIX

LEAD OF HELIX

PIRTCH DIAMETER

BASE CIRCLE DIAMETER

ADDENDUM

WHOLE DEPTH

TRANSVERSE CIRCULAR

TOOTH THICKNESS WO/BL

NORMAL CIRCULAR

TOOTH THICKNESS WO/BL

yang13564

* c. A  w2 A, a3 w
沒有人翻譯,找到了資料,不知道對不對!望高手出來指正!
        齒輪制造標準和精度等級：ANSI/AGMA 2000-A88，精度12級，全深，全倒角。
7 J  C  l' A( P* f        齒向、齒形修緣和漸開線輪廓公差按54773379圖紙規定。
9 z. R7 o3 _3 O        僅驅動齒輪鼓形修整。
        齒形壓力角20º
        節徑DP=10
        齒距：0.3142
        螺旋角：15.9355º
8 g5 [/ ~) P' r0 U4 b        在齒輪嚙合中心距5.5118”上，側隙要求在0.006” ~0.010”之間。
% b% K" h7 x% C1 X        齒輪材料：AISI 8620
        滲碳層0.025”~0.040”有效深度，表面硬度為57~61Rc，芯部硬度25~40Rc。
, g! G/ w% i( i* v% P        殘余奧氏體最大5%目測檢查。
! n  r8 o; k& C9 k        每個周轉盒內只能裝一個齒輪組，周轉盒外標記齒輪組圖號，齒輪表面須按圖示部位用電蝕法標記零件號和供貨商代碼，字高約0.25。
        攻絲后，去除螺紋孔內的鐵屑。

qvzhiwei

樓上玩意的好專業，佩服！??！

another

二樓挺專業的···感覺還不錯，很值得學習。