|
|
4#
樓主 |
發(fā)表于 2013-7-3 12:06:42
|
只看該作者
本帖最后由 寧波EN深孔加工 于 2013-7-3 12:07 編輯
6 O' \$ B! }- J) I# T* B' I9 G( o! r3 M% X2 Z$ x
O9300([A-00]GUN DRILL DRILLING CYCLE)7 l, d5 l4 }0 y# p+ L
IF[#9EQ#0]GOTO9001 }* H X5 T2 |, {! ^
IF[#18EQ#0]GOTO9001
* x# }' U0 \" Z% h9 I, KIF[#20EQ#0]GOTO9001
H! k" \% P0 sIF[#26EQ#0]GOTO9001
; ]! }$ V0 b; w7 ?; PIF[#26GE#18]GOTO90047 P2 _0 N, ~) R) b
IF[#20LT0.]GOTO9004
5 _0 Y" ~& E: T# f L3 RIF[#20GT1.]GOTO9004
) H# n& E! j! ?( x6 S0 M" P* a#1=#5003
* K. t# m' I0 {% U; o. M% PIF[#20NE1.]GOTO10001 C) Y$ | H- v& A# V: q
G90G0W#5002' m5 i, f* h: r5 N; A$ z4 p
G4X1.' A+ ^7 Q( L. X- y. ~ W4 D0 r
N1000
8 @) a2 K/ B! ^0 [0 U K7 `M10: k( V) ?/ S( D" ~
G4X1.
" g# C) R. ~# D) o! N- mM8
3 d/ n/ S2 t( W: qM3
) M7 L4 M9 I3 gG1Z#18F500
* I* d- \, `3 w* XZ0.5F50.% ~# p5 ]; x: g& i1 h% M
IF[#26GT[-8]]GOTO20008 C9 R8 r, r2 f( c& e
Z[-5.]F[#9*0.2]
0 c. V) h8 `( ]( n. f% pZ[-5.5]F[#9*0.3]. p) }" ~0 q3 U {; m- ]
Z[-6.]F[#9*0.4]
1 H; r- e% F5 |3 yZ[-6.]5F[#9*0.5]
* }; \/ U! e( t9 Y& ~4 J0 a! B( gZ[-7.]F[#9*0.6]' X( i2 S& {. O) i6 a. M
Z[-8.]F[#9*0.7]* D# a$ g# M; H& q8 L4 J
Z[-9.]F[#9*0.8]* A' A% ~; n, H9 M: i# i O/ ^
Z[-10.]F[#9*0.9]
1 D+ O# m( d; l [: T# i$ @% yN2000
2 U( e; ~: J9 F8 e2 }/ F+ ], gG1Z#26F#9, @+ a; s# }1 Y5 @
M56 P6 J/ V0 r/ g
M9: J; _0 F* z" A& M
G4X2( r: G* z3 r* E/ a4 i( d5 b
G0Z#1
9 U- _1 v2 J7 m; xM11
) X( m0 f8 x; E( t, l& n; f, ?G4X1
6 V# _" v) Q, q: c* p4 J7 {5 zM99
" ]- s1 r. m3 k$ B, i+ lN9001
1 x7 }* N; h5 N#3000=1(ARGUMENT HAD NOT BEEN SPECIFIED)6 H8 S- }/ `, _& o( h, G; @
N90047 Z5 j+ T. n0 C" Z+ p0 S. o
#3000=4(UNSUITABLE RANGE/CYCLE DEFINED)% N) p+ t- ]3 n4 @' q5 K8 z$ P, ~
1 E6 t z, d! L, n( e; l9300宏程序 |
|
發(fā)表于 2013-7-2 13:16:52
QQ好友和群
QQ空間