国产精品乱码一区-性开放网站-少妇又紧又爽视频-西西大胆午夜人体视频-国产极品一区-欧美成人tv-四虎av在线-国产无遮挡无码视频免费软件-中文字幕亚洲乱码熟女一区二区-日产精品一区二区三区在线观看-亚洲国产亚综合在线区-五月婷婷综合色-亚洲日本视频在线观看-97精品人人妻人人-久久久久久一区二区三区四区别墅-www.免费av-波多野结衣绝顶大高潮-日本在线a一区视频高清视频-强美女免费网站在线视频-亚洲永久免费
機械社區
標題:
牧野機床出現以下問題，哪個大神幫忙解決
[打印本頁]
作者:
朱一濱
時間:
2015-7-30 16:52
標題:
牧野機床出現以下問題，哪個大神幫忙解決
牧野機床出現以下問題，哪個大神幫忙解決。多謝了！
: i+ ?8 P! U6 h2 ?8 S7 ~
7 ?$ p) `. X4 r+ ?( ^! h
機床問題：
8 k& c$ V' t5 w; l
( h9 N5 o% W M3 g# k8 U$ n- x
1、SPNDL SPEED COMMAND IS NOT SET WHEN START SW，WAS PRESSED
0 R- L# `9 S9 b: k* V3 }
0 R, Q1 F# L$ W& B$ n% d6 O* u u
COMMAND S—CODE AFTER RESET ALARM
) v( N8 \) X* g' w# q
8 x: Z- f' e4 X4 o [/ H
2、NOZZLE CLANT THERMAL RELAY IS TRIPPED
c& i: o2 h" |$ K& F( @
5 b0 E2 c* @! E/ O% R
DI SIGNAL TH2... WENT ON
& \" g1 [. M8 z. z* k7 `% K
5 ^2 e. [! |: z; b( y, k2 h @. q
CHECK THERMAL RELAY AND THE BREAKER
9 g- }8 t- f6 i' x3 B- |4 S! O
) H4 p$ I9 Z5 z# b/ @+ j
3、NC ALAMRE IS BEING GENERATED
6 r, c3 L- `6 ?3 K I8 E( w0 E
* ?' q' V( O: c5 `8 u
BMI SIGNAL AL....IS ON
% B/ A% x6 _/ w( U6 G) T% g3 U
- H8 e1 d+ |: V: L; c! l+ e
CHECK FAULTY DEVICE
v+ E/ X, j M6 Z
5 {7 t+ F. H$ Q
4、TOOL CLAMP SIGNAL TOOK OFF DURING SPINDLE CW ROTATION DI SIGNAL LS00..IS OFF
0 B4 m/ Q# B c0 D$ D$ g
" _* A5 E+ y" r4 {0 E
CHECK THE CONDITION OF LIMIT SWITCH，SILENOID AND ETC
8 k0 w; ^' ?. V+ {7 [" S) A
+ J+ o- ^3 r- L* H4 p9 x1 G
5、MAN. TOOL UNCLAMP & CLAMP CANNOT PERFORM AT AUTO MODE
8 ~7 y5 S3 i$ h6 ?- y9 Z
. C' B/ p) k0 ^: t% a
SELECT CORRECT CODE
$ G& o' P* |3 {( z6 r, j4 \$ T* [. G
歡迎光臨 機械社區 (http://m.whclglass.com.cn/)
Powered by Discuz! X3.5